DDR1, 250MHz, DDR500, 2.5Volts

Manufacturer:

AMIC Technology

Part #:

A48P3616AV4F

Availability:
Contact Symmetry For Lead Time
This item is currently not available for purchase online.

Please call us at 877-466-9722 to request a quote.

 
 

Product Information

Back to top
The 128Mb DDR SDRAM uses a double-data-rate architecture to achieve high-speed operation. The double data rate architecture is essentially a 2n prefetch architecture with an interface designed to transfer two data words per clock cycle at the I/O pins. A single read or write access forthe 128Mb DDR SDRAM effectively consists of a single 2nbit wide, one clock cycle data transfer at the internal DRAM core and two corresponding n-bit wide, one-half-clock-cycle data transfers at the I/O pins.

A bidirectional data strobe (DQS) is transmitted externally, along with data, for use in data capture at the receiver. DQS is a strobe transmitted by the DDR SDRAM during Reads and by the memory controller during Writes. DQS is edgealigned with data for Reads and center-aligned with data for Writes.

The 128Mb DDR SDRAM operates from a differential clock (CK and CK; the crossing of CK going high and CK going LOW is referred to as the positive edge of CK). Commands (address and control signals) are registered at every positive edge of CK. Input data is registered on both edges of DQS, and output data is referenced to both edges of DQS, as well as to both edges of CK.

Read and write accesses to the DDR SDRAM are burst oriented; accesses start at a selected location and continue for a programmed number of locations in a programmed sequence. Accesses begin with the registration of an Active command, which is then followed by a Read or Write command. The address bits registered coincident with the Active command are used to select the bank and row to be accessed. The address bits registered coincident with the Read or Write command are used to select the bank and the starting column location for the burst access.

The DDR SDRAM provides for programmable Read or Write burst lengths of 2, 4, or 8 locations. An Auto Precharge function may be enabled to provide a self-timed row precharge that is initiated at the end of the burst access.

As with standard SDRAMs, the pipelined, multibank architecture of DDR SDRAMs allows for concurrent operation, thereby providing high effective bandwidth by hiding row pre-charge and activation time.

An auto refresh mode is provided along with a power-saving Power Down mode. All inputs are compatible with the JEDEC Standard for SSTL_2. All outputs are SSTL_2, Class II compatible.

The functionality described and the timing specifications included in this data sheet are for the DLL Enabled mode of operation.
 

Features

Back to top
Differential clock inputs (CK and CK )
Four internal banks for concurrent operation.
Data mask (DM) for write data.
DLL aligns DQ and DQS transitions with CK transitions.
Commands entered on each positive CK edge; data and data mask referenced to both edges of DQS.
Burst lengths: 2, 4, or 8
CAS Latency: 2/2.5/3/4
Auto Precharge option for each burst access
Auto Refresh and Self Refresh Mod
4096 refresh cycles / 64ms (4 banks concurrent refresh)
2.5V (SSTL_2 compatible) I/O
VDD = VDDQ = 2.5V 0.2V
Industrial operating temperature range: -40C to +85C for -U series.
Available Lead Free packaging
All Pb-free (Lead-free) products are RoHS compliant
Double data rate architecture: two data transfers per clock cycle.
Bidirectional data strobe (DQS) is transmitted and received with data, to be used in capturing data at the receiver.
DQS is edge-aligned with data for reads and is centeraligned with data for writes.
 

Documents

Back to top
Datasheet

Previously Viewed Products

DDR1, 250MHz, DDR500, 2.5Volts
Part #: A48P3616AV4F
DDR1, 250MHz, DDR500, 2.5Volts