XPort embedded Ethernet device server removes the complexity – of designing network connectivity into a product by incorporating all of the required hardware and software inside a single embedded Ethernet solution. Smaller than your thumb, it includes all essential networking features, including a 10Base- T/100Base-TX Ethernet connection, proven operating system, an embedded web server, e-mail alerts, a full TCP/IP protocol stack, and 256-bit AES encryption for secure communications. This easy-to-embed networking processor module enables engineers to focus on their core competency while reducing development time and cost and increasing product value. - Minimal engineering effort required to web-enable virtually any electronic device
- Remote command and control of edge devices
- 256-bit AES encryption for secure communications
- EMC/EMI-compliant; RoHS-compliant
- Everything you need — all in a single RJ45 package
XPort is powered by our DSTni™ network processor SoC, which includes a 10/100 MAC/PHY and 256 KB of SRAM. It features a built-in web server for communications with a device via a standard Internet browser. Web capability can be used for remote configuration, real-time monitoring or troubleshooting. XPort has 512 KB of onmodule Flash for web pages and software upgrades. It acts as a dedicated co-processor that optimizes network activities permitting the host microprocessor to function at maximum efficiency.
With XPort you can embed intelligence into any electronic product for applications such as:
- Remote diagnostics and upgrades
- Asset tracking and replenishment
- Automation and control
- Power management
- Remote collaboration
- Personalized content delivery
- Robust, Feature-Rich Software Suite
Eliminating the need to negotiate the intricacies of Transmission Control Protocol (TCP) or Internet Protocol (IP), XPort incorporates:
- Robust Real Time Operating System (RTOS)
- Full-featured network protocol stack
- Built-in web server for device communication and configuration via a standard browser
The Windows-based DeviceInstaller™ makes configuring one or more XPorts in a subnet quickInstall and configure XPort and load firmware and easy:
- Install and configure XPort and load firmware
- Assign IP & other network specific addresses
- Load custom web pages and view specific device data
- Enable web-based configuration of the device
- Ping or query the attached device(s) over the network
- Allow Telnet communication with the device(s)
Features
- Interface:
- CMOS (Asynchronous, 5V Tolerant)
- Data Rates:
- 300 bps to 921,600 bps
- Characters:
- 7 or 8 data bits
- Parity:
- odd, even, none
- Stop Bits:
- 1 or 2
- Control Signals:
- DTR/DCD, CTS, RTS
- Flow Control:
- XON/XOFF, RTS/CTS
- Programmable I/O:
- 3 PIO pins (software selectable)
- Interface:
- Ethernet 10Base-T or 100Base-TX (Auto-Sensing)
- Connector:
- RJ45
- Protocols:
- TCP/IP, UDP/IP, ARP, ICMP, SNMP, TFTP, Telnet, DHCP, BOOTP, HTTP, and AutoIP
- Indicators (LED):
- 10Base-T connection
- 100Base-TX connection
- Link & activity indicator - Full/half duplex
- Management:
- SNMP, Telnet, serial, internal web server, and Microsoft Windows®-based utility for configuration
- Security:
- Password protection
- Optional 256-bit AES Rijndael encryption
- Storage Capacity:
- 384KB for web pages
- CPU:
- Based on the DSTni-EX enhanced 16-bit, 48MHz or 88MHz, x86 architecture
- Memory:
- 256KB SRAM and 512KB flash
- Firmware:
- Upgradeable via TFTP and serially
- Input voltage:
- 3.3 VDC
- Operating Temperature Range:
- -40° to 85°C (-40° to 185°F)
- Storage:
- -40° to 85°C (-40° to 185°F)
- Dimensions:
- 33.9 x 16.25 x 13.5mm (1.33 x 0.64 x 0.53 in)
- Weight:
- 9.6 g (0.34 oz)
